Products Directory > Electronics & Electrical > Active Devices >
Pressure Transducers
Displaying 1-14 Products of Total 15 Products Found
-
Products
- Description
- Supplier Information

The pressure transmitter and pressure transducer are used when output in terms of mA or mV is required in proportion to the pressure available in process vessel. These are available with SS 316 wetted parts for a range of few mmWc to 1000 bar in IP 65 as well as flameproof enclosure. These can be provided either blind type or with Digital Readout. We provide then in accuracy of 1%, 0.5%, 0.25% as per customers requirement.
0 to 760 mm Hg Vacuum or
0 to 500 mmWc up to 0 to 1000 Bar
Blind type or Digital indicating type
Excitation - 12 to 36 V DC
Out put - 4 to 20 mA
Accuracy +/- 0.25%, 0.5% or 1% FSD
Casing SS 304 for Blind Transmitter and Industrial Plastic for Indicating Transmitter
Enclosure - IP 65 or Flameproof
Internals SS 304, SS 316 or special on request
Process Connection Threaded or Flanged
Application - For Indication & Control of Pressure & Vacuum in proportional mode
![]()

Consists of - High Pressure Monitoring Lines, Transducers Domes, Flushing Devices, Three way Stop Cock.
Assembled as per customer's specifications.
E.T.O. Sterile & Pyrogen Free.
![]()

We offer a full range of Position Transducers manufactured by Novotechnik, Germany.
Linear Transducers Potentiometric
Stroke lengths from 10mm to 3000mm
Return spring version available
Resolution better than 10 microns
Life expectancy greater than 100 million operations
Linear Transducers Non-contact
Stroke lengths from 100 to 4500mm
Resolution better than 1 micron
Choice of analog or digital (Encoder, SSI, Start-Stop) outputs
Direct integration into hydraulic cylinders possible
Rotary Transducers Potentiometric
Electrical travel up to 360 degrees
Shaft diameter: 3, 6 or 10mm
Resolution better than 0.007 degree
Life expectancy greater than 50 million operations
Rotary Transducers - Non-contact
Electrical travel up to 360 degrees
Resolution: 12 bit
Truly touch-less version available for transmissive measurements
Unlimited mechanical life- Accent Controls Private Limited
![]()

Pressure transduceres for electrical oil pressure gauges are avialable in 0-7Kg/ cm2 and 0-10kg/cm2. Robustly built with accuracy and fully calibrated, electrical oil pressure gauges in NS designs available in 52mm/ 60mm dia. Pressure switch in available with S.P.DT switch, Diaphragm type construction ideal for engines, generator for low lube and crank case oil pressure.
- India-Shine Exporters
![]()

We offer a wide range of highly reliable incremental encoders, which have high resolution from 2PPR to 2500PPR and have 2 to 6 channels. Having I/P Voltage 5V DC to 23V DC, its encoder diameter is available in 40mm, 50mm, & 58mm. We offer them in both imported and Indian models.
- Tachometric Controls
![]()

We design and manufacture electronoc pressure transducers for general measuring tasks, with internal or flush stainless steel diaphragm, linearity error 0.5% f.s
Features more...- Icon Hydraulik
![]()

We offer industrial thermometers (Straight V type) to our clients. These are available in range from 95°C to 205°C and 100°C to 300°C. Besides degree Celsius, we also manufacture these in Fahrenheit, Kelvin scale. Availbale in both standard & customized range, these meet the process demands of tyre industry, chemical industry and process control industries.
- Charu Chemical Laboratories
![]()

We manufacture and supply a broad range of transducers that are used in diversified industries to convert one type of energy to other. These products are widely used to measure different factors and convey information. The product range includes following features: more...
- Sushma Industries
![]()

Signal Isolators of our brand is also known as transducers are mainly utilized in process control system. This isolators are mainly used only when there is a ground loop problems, to protect the transmitting and receiving instruments (PLC, DCS) or where there is a requirement to carry the signaling process for long distance that is used for converting the voltage signal to current signal with excellence and accuracy.
In fact signal isolators of our brand provide total signal isolation between a non- isolated materials and a receiving device. Actually this reduces faulty reading in process of measurement and control equipment.- Integra Electronics
![]()

The output signals of encoders are to be interpreted in the form of position to be shown digitally and outputted in analog form or RS485. The Digital Transducer EDA-201 can accept signals from Absolute single or Multiturn encoders in Synchronous Serial Interface form or Parallel Binary or Grey form.It can be scaled to give meaningful reading corresponding to rotary or linear position e.g. degree, millimeters,etc. Additionally it gives analog signal in 4-20mA correspondingly. It can also accept pulses(square wave)from incremental encoders. Another digital transducer(Pulse Tachometer)PST-201 is made to interpret speed,scale it to desired parameters e.g. rpm, meters per minute,etc. display and give 4-20mA output.
Other blind transducers like signal converters SPG-3 convert SSI to parallel outputs for absolute encoders. Yet another range of interface transducers e.g. INTC5, INTC50 are meant for incremental encoders for compatibility to users input, are available in different more...- PG Electronics
![]()

We design and manufacture low cost pressure transmitter that are high in performance and durable and widely used for numerous applications.
MSP-600: New High Accuracy Digital Compensated EMI/RFI Protected Stainless Steel Isolated Pressure Transducer
Features: more...- Tempsen Devices
![]()

Features
more...- Structural Solutions
![]()

The shaft incremental encoders are precision measuring instruments to transduce position, distance angle or speed. The PGcoders EN-801, EN-901 are indigenously manufactured with precision technology.
These Incremental encoders register position of the shaft driven by users drive through a coupling. Output is available in form of square pulses incremented (or decremented) step by step in users counter or PLC. Direction can be determined with the help of two trains of pulses running in quadrature. One index pulse is available per rotation for orientation of mechanical position.
PGcoders are extensively used in automation industry in machine tool, metal cutting, paper, rubber industry, etc. All our encoders are now available with CЄ compliance.
· CЄ compliant incremental encoders
· Differential outputs for channels k1,k2 and k0
· Precision ranges upto 10,000 ppr Series EN - 801
· Medium ranges upto more...- PG Electronics
![]()

The shaft incremental encoders are precision measuring instruments to transduce position, distance angle / speed. The PGcoders EN-801P, EN-801H & EN-201 are indigenously manufactured with precision technology. The basic encoder type: EN-801/ EN-901 is incorporated in heavy duty housing type `H and `P. The base mounted encoders are type designated as EN-801H / EN-901H and the flange mounted encoders as EN-801P.
These Incremental encoders register position of the shaft driven by users drive through a heavy-duty coupling. Output is available in form of square pulses incremented (or decremented) step by step in users counter or PLC. Direction can be determined with the help of two trains of pulses running in quadrature. One index pulse is available per rotation for orientation of mechanical position.
PGcoders are extensively used in automation heavy industry like Steel & Pipe mills, Non-ferrous, Material handling plants & other industry, where long cable more...- PG Electronics
![]()

